Parts Washers

An Environmental and Operational Safe Parts Washing System using an Aqueous Bio-Premeditating / Enzymatic Cleaning Process

Spray Pressure Wash Flow-through Brush Soak Cleaning Agitation Multi-Functional - Operator Friendly and Fast Cleaning - Unattended Operation that saves Time Stainless Steel Construction - Long Life with Low Maintenance - Easy to Clean with No Rust - Latchable Cover that is sealed - 50 year Limited Warranty Removable Shelves and Baskets - Large or Small Parts Water Based Bio-Fluid Cleaner - No Chemical Solvents - Bioremediation Process - Non-Toxic By-Products - Rust Inhibitor - USEPA NCP Listed South Coast AQMD Clean Air Solvent Certified Operator Safety - Non-Flammable Fluid - Bio-Safe and Non-Irritating - Intrinsic Safe Design, with GF Minimal Non Hazardous Waste GSA Contract # GS-07F-0414J DLA NSN’s for all models ABC Approved Bio-Fluid Supplied Patent Pending on System

An Environmental and Operational Safe Parts Washing System using an Aqueous Bio-Premeditating / Enzymatic Cleaning Process

The“American Bio-Clean Parts Cleaner" is designed to meet today's stringent environmental and occupational safety and health regulations.

The systems proprietary bio-remediation process uses a heavy duty, solvent free, aqueous (water) based fluid that quickly and efficiently emulsifiers, degreases, and disperses hydrocarbon deposits and dirt. Biologically safe microorganisms the(--) metabolize the grease and oil into harmless carbon dioxide and water. “American Bio-Clean Parts Cleaner” are constructed of long-lasting, corrosion-resistant, stainless steel which most maintenance problems.

Specifications:

• Electrical- UL Approved components
• Steady Flow 44 gpm Stainless Steel Pump ½ HP, 120 V, 60 Hz, 8.6 Amps
• Stainless Steel Strip Heaters (2) 500 Watts, 120V
• Cal-Stat Thermostat: 95 degrees to 105 F degrees
• Safety (OSHA) Foot Switch with Cord: 120 V
• Industrial Water and Shock Resistant Lamp
• That is 120 V/UL Listed
• On / Off System Switch: 20-120 V-Green
• Light On Indicator
• Ground Fault Interrupter Power Plug

55 FH and HT Models

• Capacity – 55 Gallons
•  Work Area- 43” L x 22” W x 17” H
• Outer Dimen, 62”L x 44”W x 80”H
• Weight Full – 1,030 lbs. / Empty – 575 lbs.

Special Design Models

• CAPACITY – Up to 10,000 Gals
• Dimensions- To Specifications
• Weigh –to Requirements

Mechanical

• Fluid filters – 500, 300, 200, 80, and 22 Micron
• Multi-Stage Reusable filter elements
• Reusable filter elements
• 2 Remote Filter Housings
• Easy Drain/Clean out Flow-Thru Brush with Nylon Reinforced Hose
• Tank Bottom Clean-Out Ball Valve – 1.25 Inches

Pneumatic

•  Electric Air Pump- continuous Duty

Options Available

• Small Parts Containment Soak Basket
• Air-Blown Dryer (30 PSI / OSHA Safe
• Special Cleaning Tools

INDUSTRIAL, QUALITY DESIGN FEATURES:
Electrical and operating mechanical components of all ABC parts washers are mounted on the exterior for simple inspections and maintenance without removing the Bio-Clean Washer fluid. External Heaters and thermostat automatically maintain the Bio-Clean fluid at factory set 105 degrees to 115 degrees F. facilitating microbial activity and the enzymatic cleaning process. Foot actuated operator on-off switch and hand on-off unattached operational switch. Pump is securely fastened under the washer tank and recycles the bio-fluid as it is used.

No Filter replacement required - reusable, cleanable, long-life stainless steel filter elements. 50 Year warranty on stainless steel tank housing and structural components upon submittal of warranty registration.

ENVIRONMENTAL HEALTH WARNING
Introduction of hazardous substances into an ABC Parts Washer may result in hazardous fluids and /or residue solids. Disposal filter residue, sludge and fluids should be in accordance with applicable local, state and federal environmental, health and safety laws and regulations.
 

what is had on this page.

 ABC Parts Cleaners are multi ‑functional, multi‑process designs, offering:

• hand brush pressure spray washing
• unattended pressure spray washing

• unattended soak agitation cleaning, simultaneous with above.

Specifically, the unit shall be used for remediation of oils, solvents, greases, ethylene glycol, and chlorinated hydrocarbons. Stainless steel tank housing, latch down cover, handle, lamp mounting and legs. All exposed system components are rust/corrosion resistant to withstand seaboard atmospheric conditions. Unit lid is clamp lockable in the closed position and spring loaded and cam secured for operation safety in the open position. All electrical components are mounted separately and externally from the housing/reservoir containing, the cleaning fluid. The unit is equipped with an integral GFI system on the electric power cord for user safety.

ABC Parts Cleaning Models
55HT301 Wheels and Fork Lift Bracket
55FH001 - Standard
55FH101 with Wheels and Handle
55FH201 with Forklift Brackets
55FH301 with Wheels and Forklift Brackets

	22 Gallon Small Sink Basic P/N: 22FH001
	40 Gallon Basic Parts Washer P/N: 40FH001 NSN: 4250-01-466-9611 --with wheels and handle P/N: 40FH101  NSN: 4250-01-466-9607
	55 Gallon Basic Parts Washer P/N: 55FH001    NSN: 4250-01-466-9597 with wheels and handle P/N: 55FH101 NSN: 4250-01-466-9622 with forklift brackets P/N: 55FH201 - NSN: 4250-01-466-9618 with forklift brackets, wheels and handle P/N: 55FH301 - NSN: 4250-01-466-9614
	55 Gallon Paint Can Washer Basic Unit P/N: 55FC001
	80 Gallon Parts Washing Unit P/N: 80FH401 with wheels, handle, forklift brackets, 1 air dryer (lift back top)
	250 Gallon Large Equipment Cleaner P/N: 250LE301 with wheels, handle, forklift brackets, 4 wash stations (lift Back top)

ABC Equipment is designed specifically as a Cleaning System with its associated bio-remediating cleaning fluid to support and optimize the cleaning and bio-remediating processes.

Parts Cleaning (PC) Fluid
P/N PC030PMM DLA NSN# 6850-01-449-6018

Weapons Cleaning (WC) Fluid
P/N WC030PMM DLA NSN# 6850-01-473-2706

GSA Contact –GS-07F-0414J - On Specified Cleaners (*)

Top